The battery may be more expensive

    The battery may be more expensive

    All companies are constantly looking for ways to save money, but when they buy forklifts, electric cars, and sweepers, they may be buying at the lowest price initially, but they may have to look at long-term benefits. Pay more.

    When battery engineers design traction batteries and battery chargers, they may be affected by suppliers. It is possible to design a battery that is inexpensive for practical use and a basic charger. Of course, this will inevitably lead to Higher fuel costs and shorter battery life.

    In order to achieve the lowest price for purchasing equipment, the importance of charger and battery pairing is often overlooked by many customers. Therefore, it is best for the charger and the battery to be the same manufacturer, and to maximize the usefulness of the device's life and efficacy.

    The problem with inferior batteries is that the lead contained in it is of low quality and capacity. As a result, this will lead to a reduction in the amount of charge generated by the increased use of the battery, which will eventually lead to a decrease in the entire life cycle.

    Low-cost batteries are not only prone to accidents and react poorly to overcharge, but also cause battery capacity to drop. This is often repeated, then it means that you need to replace the battery to avoid too little power output and affect the normal use of the vehicle.

    Anti Strong Impact Abrasive Wear Plate

    hard-faced wear-resistant steel plate is a premium grade, permanently-bonded chrome carbide overlay plate made for the most severe abrasive wear environments.

    the high density of chrome carbide crystals in a tough alloy matrix act like the stones in concrete. As the concrete pavement wears, the stones provide a surface that resists abrasion better than the cement in which they are embedded. The chrome carbides serve the same purpose, providing an ultra hard microstructure that resists wear longer than the alloy steel around them.

    *HP400 (Resistance to strong impact abrasive wear)

    HP400 hard-faced wear-resistant steel plate is suitable for the working condition of high stress and strong impact abrasive wear.

    Hard-facing layer main chemical composition of metal (Wt%)

    C

    Cr

    Mn

    Other

    0.4~1.5

    3~7

    15~22

    2~5


    Hard-facing layer normal hardness: 20-25HRC

    After the cold work and hardening hardness:50-55HRC

    Wear resistant temperature: <500℃

    Anti Strong Impact Abrasive Wear Plate,Abrasion Resistant Plate,Abrasion Resistant Steel Plate,Resistance To Strong Impact Plate

    SHENYANG HARD WELDING SURFACE ENGINEERING CO.,LTD , https://www.hardfacingplate.com

    Previous Post: Dana and Dongfeng Commercial Vehicle Cooperate with Axle to Start Production in Early Next Year
    Next Post: Tiankang Silicone Rubber Cable Development Trend
    Home
    Recent Posts
    • Sound heard trailer malfunction
    • With so many flow meters, these motion pictures …
    • The First Global 5G Conference Held by Miao Wei,…
    • Uber received $3.5 billion in financing
    • Space data highway development in Europe: 1.8 gi…
    • Analysis of Causes of Black Smoke in Sewage Pump…
    • Garbage truck tire selection
    • Shandong Yinbao Tire Group Adds a National Inven…
    • MCU + Sensor: IoT market occupied with cheap and…
    • the Dragon Boat Festival is coming
    • Hefei smart three roller gate performance profil…
    • ·Changzhou, Jiangsu: Legislation to ensure bus …
    • How to choose a vacuum transformer oil purifier?
    • Hangzhou Water Meter "Intelligent Water Aff…
    • "Twelfth Five-Year Plan": Seven Major …
    • Hainan: Introduced advanced environmental protec…
    • How to maintain the car's generator?
    • Brazil launches anti-dumping investigation again…
    • Yuyao, Zhejiang 11 printing and paper products c…
    • Not only the engine Yuchai is enthusiastic about…