Extending the life of forklift clutch release bearing The internal bearing of the fork-lift truck clutch works frequently. The number of damages accounts for a large proportion of the failure of the forklift. If the driver operates properly and maintains it in time, this bearing can be used for about 3 months, but in When it is time for repairs, it should be replaced. If the driver's technical level is low, the driven forklift will damage the separated bearing almost every month, and will also suffer from other components after the damage, such as the release lever and the clutch plate, so that the material cost for equipment maintenance will be significantly improved.
What is the reason for the damage of the clutch release bearing? In practice, although the driver was once strictly required to drip oil once a day to separate bearings, this operation was not only cumbersome, but also the bearings were often damaged. After analysis, because the engine's high temperature is transmitted to the separate bearings, coupled with the high-speed rotation of the bearings also produce high temperatures, in this condition the oil is difficult to remain in the bearing, the bearing works continuously at high temperatures, and the lubrication conditions are not good, this is Frequent damage causes.
In response to the above problems, it has also been tested that the bearing is placed in the grease to heat it, so that the grease penetrates into the bearing. After the treatment, the grease can fill the bearing, but the structure of the grease after high temperature treatment is damaged and the performance is high. Reduced amplitude, the use of this method is not ideal, the bearing life is not extended. We have also used butter guns to directly inject butter into the separate bearings. Then install the car, after inspection and inspection, the bearing life is greatly extended. This method of injection has received satisfactory results, but the operation is more complicated. Then he explored how to add butter when the engine did not disintegrate. He first tried successfully on the 475C engine, and later on the 475C and 480, 492 engines, all received good results. After repeated practice, improvement, and summing up experience, a relatively simple set of oil filling operation methods was finally formed. The specific process is as follows:
(l) Engine disintegration method First, open the clutch cover and observe the wear condition of the release bearing. If it is confirmed that the bearing is not damaged or the wear does not exceed the limit, remove the clutch pedal, adjust the connecting rod pin, and separate the bearing and its The seat is retracted to the final position. Grease the bore of the bearing housing with a sharp-nosed grease gun until the bearing oil has spilled. Then rotate the bearing a little and refill the oil. Repeat until the bearing has a little butter around it. Rotate the bearing and observe the amount of oil. If you feel the resistance of the bearing turning, prove that the bearing has been filled with butter. Then remove a small amount of grease that has come out of the separate bearing housing and reassemble the removed pin and clutch cover.
(2) Disassembly of the engine by disassembly of the engine exposes the disassembled parts of the engine to the bearing and bearing assembly. Use a needle grease gun to refuel the small oil hole below the inner ring of the bearing housing. When the grease overflows, the bearing rotates until it reaches the bearing. All circles have butter overflow.
After the above two methods are processed, the bearing can be no longer refueled within six months. After this set of oil injection method was tested at the Hengshui Railway Station, the mechanical integrity rate was significantly improved and obvious economic benefits were achieved. The material cost can be saved; the amount of loading and unloading can be increased, and each month can increase the loading and unloading capacity by 30 tons. This method has also been promoted at other railway stations and has achieved satisfactory results.
What is the reason for the damage of the clutch release bearing? In practice, although the driver was once strictly required to drip oil once a day to separate bearings, this operation was not only cumbersome, but also the bearings were often damaged. After analysis, because the engine's high temperature is transmitted to the separate bearings, coupled with the high-speed rotation of the bearings also produce high temperatures, in this condition the oil is difficult to remain in the bearing, the bearing works continuously at high temperatures, and the lubrication conditions are not good, this is Frequent damage causes.
In response to the above problems, it has also been tested that the bearing is placed in the grease to heat it, so that the grease penetrates into the bearing. After the treatment, the grease can fill the bearing, but the structure of the grease after high temperature treatment is damaged and the performance is high. Reduced amplitude, the use of this method is not ideal, the bearing life is not extended. We have also used butter guns to directly inject butter into the separate bearings. Then install the car, after inspection and inspection, the bearing life is greatly extended. This method of injection has received satisfactory results, but the operation is more complicated. Then he explored how to add butter when the engine did not disintegrate. He first tried successfully on the 475C engine, and later on the 475C and 480, 492 engines, all received good results. After repeated practice, improvement, and summing up experience, a relatively simple set of oil filling operation methods was finally formed. The specific process is as follows:
(l) Engine disintegration method First, open the clutch cover and observe the wear condition of the release bearing. If it is confirmed that the bearing is not damaged or the wear does not exceed the limit, remove the clutch pedal, adjust the connecting rod pin, and separate the bearing and its The seat is retracted to the final position. Grease the bore of the bearing housing with a sharp-nosed grease gun until the bearing oil has spilled. Then rotate the bearing a little and refill the oil. Repeat until the bearing has a little butter around it. Rotate the bearing and observe the amount of oil. If you feel the resistance of the bearing turning, prove that the bearing has been filled with butter. Then remove a small amount of grease that has come out of the separate bearing housing and reassemble the removed pin and clutch cover.
(2) Disassembly of the engine by disassembly of the engine exposes the disassembled parts of the engine to the bearing and bearing assembly. Use a needle grease gun to refuel the small oil hole below the inner ring of the bearing housing. When the grease overflows, the bearing rotates until it reaches the bearing. All circles have butter overflow.
After the above two methods are processed, the bearing can be no longer refueled within six months. After this set of oil injection method was tested at the Hengshui Railway Station, the mechanical integrity rate was significantly improved and obvious economic benefits were achieved. The material cost can be saved; the amount of loading and unloading can be increased, and each month can increase the loading and unloading capacity by 30 tons. This method has also been promoted at other railway stations and has achieved satisfactory results.
HDPE Extrusion Blowing Machine
Started in 2006, we've been specializing in blow molding technology. A sample of products produced by WATON machinery includes dairy bottles. shampoo bottles, detergent bottles, beverage bottles, lubricant containers, pesticide containers, hollow toy, extruded pallets and other large plastic products.
Hdpe Extrusion Blowing Machine,Automatic Extrusion Blow Molding Machine,Hdpe Bottle Blowing Machine,Bottle Extrusion Blow Molding Machine
TAIZHOU WATON MACHINERY CO LTD , https://www.watonblowings.com