Mining capacity: 4m 3 / day and night pressure: 20 MPa (200ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-6.3-1500 Electric Pump:
Mining capacity: 6.3m 3 / day and night pressure: 15 MPa (150ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-8-1300 Electric Pump:
Recovery: 8m 3 / Day and Night Pressure: 13 MPa (130ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-10-1200 electric pump:
Mining capacity: 10m 3 / day and night pressure: 12 MPa (120ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-12.5-900 Electric Pump:
Mining capacity: 12.5m 3 / day and night pressure: 9 MPa (90ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-16-750 Electric Pump:
Mining capacity: 16m 3 / day and night pressure: 7.5 MPa (75ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
EDN5-20-600 electric pump:
Mining capacity: 12m 3 / day and night pressure: 6 MPa (60ÐºÐ³Ñ / кв.Ñм). Power is not more than 3KW Diameter: 117mm Length: 2700 mm Weight: less than 125kg
product description:
Used for low yield bending, inclined shaft oil extraction, practical for oil viscosity of not more than 50 CCT, paraffin content of not more than 6%, diameter of not less than 121.7cm.
Require well fluid indicator:
Associated water any content
Associated LPG maximum, 10
Hard content% (g / L) 0,2 (2)
Hydrogen sulfide content% (g / l) 0,001 (0,01)
Half-water hydrogen value рР6,0-8,5
Well fluid temperature о С 5-90о
advantage:
Pump high efficiency 27 to 40% (different models)
The main working parts are located in clean oil, well fluid isolation, wear small.
Wellhead installation is simple, single pump into the well.
No need to fix the ground and large base.
Small-diameter pump can be used to compress the tube, low maintenance costs.
Can be used for continuous production of very low production wells to avoid damage to the reservoir by periodic mining.
Use SHDN01-93U1-type control equipment.
Extend the time between well maintenance and increase output.
composition:
The UEDN5 package includes EDN5 electric submersible diaphragm pumps with 3 or 5.5 kW PEDD motors , ancillary equipment for control and protection, electrical contact pressure gauges, manometer tubes, sewer tubes and sewer tubes, note Liquid valve and with (spare) pieces. Depending on the structure and the type of motor, a standard sub-list of 14 devices is formed .
Compared with other manufacturers, our products have the following characteristics: The factory independent manufacturing and more major components - pumps, motors, control equipment. Parts have to undergo a rigorous test simulation test to ensure quality. Shelf life: 12 months from the date of installation.
Electric pump mechanism:
Type pump is a single pump EDN5 by a four-pole induction motor, speed reducer and a tapered piston pump with an eccentric drive and a round-trip spring components. All parts are in the same housing and the housing is filled with oil. Isolate the housing from the well using a rubber membrane and a compensator. The top of the pump is fitted with a connector for connecting the cable . Pumps are filled with oil and tested in the production facility.
SHDN 01-93 U 1 type supporting control equipment:
Control electric submersible diaphragm pump according to the set parameters to ensure that it does not deviate from the set value. Composition: a cabinet-type device, which contains the power distribution system, control system, and motor start-up, monitoring and disconnecting device. Control mode: manual, automatic control, remote control. The equipment has the following protection functions: 380V power system short-circuit protection; into a single maximum current value, can be any one of the current overload protection; leading to the pump can not improve the ground current protection; low voltage protection.
Electric contact pressure gauge:
Used to monitor the outlet pipe pressure, when the pressure is higher or lower than the set value, automatically cut off the pump.
Pressure gauge tube:
Used to connect the pressure gauge and the oil outlet pipe and protect the pressure gauge from well fluid damage.
Sludge pipe and upper sludge pipe:
Decompression rafts to protect the pump are not blocked by solids in the well fluid.
network:
Used to prevent solids from falling to the gas separator and suction valve.
Injection valve:
Used to inject liquid from the cavity of the pump compression tube when lifting the pump from the well.
With (spare) parts:
For routine repairs. Includes: a diaphragm, a suction valve, a pressure relief valve, four centrifugal bearings , two seals and other consumables.
Their respective countries: Russia Manufacturer: STARKY
Address: 426062, Russia, Izhevsk Sports Road 111
Xinxiang sunrise NC equipment Limited by Share Ltd is a leading supplier of bearing CNC equipment, specializing in the production and sale of bearing rings, rolling development of CNC equipment, CNC equipment.
, high precision Cnc Vertical Lathe, precision plane grinding as the representative of the complete bearing CNC equipment products to CNC Ball Bearing Ring grinding, products up to more than 150 species. Is the current domestic bearing CNC equipment manufacturing enterprises in product variety is the most professional manufacturer of complete bearing CNC equipment.
The company since its inception, always adhere to the "dedication based, personality wins" the enterprise idea, technological progress and industrial upgrading is committed to Chinese bearing equipment, in the process of continuous development, fully practice "we grow together with the company, our common development" and the customer enterprise values. Both the bearing rings CNC equipment field, or bearing rolling body "light, grinding, lapping" CNC equipment field, the company's market share in the industry.
Cnc Grinding Machine,Universal Cnc Machine,Center Hole Finish Processing,Cnc Center Hole Grinding
Xinxiang Sunrise CNC Bearing Equipment Co., Ltd. , https://www.cncsunrise.com