***In-Stock Supply Specifications***
Size 1/4-20 up to 5/8 inch UNC
Size M6-1.0 up to M16
Other sizes customized
More Standard Wing Nuts
DIN315, DIN316, ANSI b18.6
Size: M3 to M16 (more sizes available upon order)
Class/Grade: 5, 8
Surface: PL, zinc, brass, NICKLE
All standard specifications please visit our Online catalogue www.hexnuts. cn
All metric and inch standards
Carbon steel C1010, Q235, C1020
Stainless Steel 18-8, SS201, SS301, SS304, SS316
Grade A2-70. A4-80
size M6 up to M16 and other specifications available after order production.
our standard Supplies as follows:
DIN315 Wing Nuts with rounded wings, DIN 316 Wing Nuts, JIS B1185-1994 Wing Nuts.
ASME/ANSI B18.6. X-2002 Wing nuts Square Wing, ASME/ANSI B 18.6. 9-2010 Wing Nuts.
ASME B18.6. X- 2002 Type A, Type B, Type C, Type D and High Wing Nuts by Pressure Casting.
Below specifications are for DIN315 standard
DIN315 Tech Data
| d1 | d2 | e | g | h |
| M4 | 6 | 18 | 1.7 | 8.5 |
| M5 | 8 | 24 | 2.3 | 11 |
| M6 | 10 | 30 | 2.7 | 15 |
| M8 | 13 | 36 | 3.6 | 18 |
| M10 | 17 | 48 | 4.6 | 23 |
| M12 | 20 | 62 | 5.6 | 31 |
| M16 | 26 | 70 | 6.5 | 35 |
| M20 | 32 | 86 | 7 | 44 |
| M24 | 41 | 106 | 8.6 | 53.5 |
WING NUTS ---DIN 316 Wing Nuts, JIS B1185-1994 Wing Nuts.
ASME/ANSI B18.6. X-2002 Wing nuts Square Wing, ASME/ANSI B 18.6. 9-2010 Wing Nuts.
ASME B18.6. X- 2002 Type A, Type B, Type C, Type D.....
Refer products &specification :
 DIN315 Stainless Steel Butterfly Wing Nuts
***In-Stock Supply Specifications***
Size 1/4-20 up to 5/8 inch UNC
Size M6-1.0 up to M16
Other sizes customized
More Standard Wing Nuts
DIN315, DIN316, ANSI b18.6
Size: M3 to M16 (more sizes available upon order)
Class/Grade: 5, 8
Surface: PL, zinc, brass, NICKLE
All standard specifications please visit our Online catalogue www.hexnuts. cn
All metric and inch standards
Carbon steel C1010, Q235, C1020
Stainless Steel 18-8, SS201, SS301, SS304, SS316
Grade A2-70. A4-80
size M6 up to M16 and other specifications available after order production.
our standard Supplies as follows:
DIN315 Wing Nuts with rounded wings, DIN 316 Wing Nuts, JIS B1185-1994 Wing Nuts.
ASME/ANSI B18.6. X-2002 Wing nuts Square Wing, ASME/ANSI B 18.6. 9-2010 Wing Nuts.
ASME B18.6. X- 2002 Type A, Type B, Type C, Type D and High Wing Nuts by Pressure Casting.
Below specifications are for DIN315 standard
DIN315 Tech Data
| d1 | d2 | e | g | h |
| M4 | 6 | 18 | 1.7 | 8.5 |
| M5 | 8 | 24 | 2.3 | 11 |
| M6 | 10 | 30 | 2.7 | 15 |
| M8 | 13 | 36 | 3.6 | 18 |
| M10 | 17 | 48 | 4.6 | 23 |
| M12 | 20 | 62 | 5.6 | 31 |
| M16 | 26 | 70 | 6.5 | 35 |
| M20 | 32 | 86 | 7 | 44 |
| M24 | 41 | 106 | 8.6 | 53.5 |
WING NUTS ---DIN 316 Wing Nuts, JIS B1185-1994 Wing Nuts.
ASME/ANSI B18.6. X-2002 Wing nuts Square Wing, ASME/ANSI B 18.6. 9-2010 Wing Nuts.
ASME B18.6. X- 2002 Type A, Type B, Type C, Type D.....
Refer products &specification :
Â
Continuous Waste Plastic Pyrolysis Plant
Pyrolysis Plant is used for recycling waste tire, waste plastic, waste rubber to fuel oil. According to the actual situation in every country and district, we developed different models of Batch Pyrolysis Plants for waste tires, rubber and plastic with daily capacity 25-40 tons.
Flow-chat of Continuous Waste Plastic Pyrolysis Plant
Advantages of Continuous Waste Plastic Pyrolysis Plant
1. Large daily capacity of 25 MT raw materials, and can work 24 hours without any stop for 15-20 days;
2. Auto-loading, auto-discharging and oil coming out at the same time;
3. Only need fuel for the beginning 2-3 hours, then the sync gas generates itself is enough to support heating, saving fuel cost;
4. Low requirement on the raw materials, no need tiny granule, 5cm pieces acceptable for smooth running;
5. High efficiency condensers, more oil output, good quality oil, easy to clean.
6. Sync gas recycling system, fully burned after recycling and utilization, preventing pollution and saving fuel cost.
7. National patent smoke scrubber, can efficient remove the acid gas and dust of the smoke, environmental friendly to meet related national standards.
8. Easy to operate, need less manpower.
Technical Parameter of Continuous Waste Plastic Pyrolysis Plant
|
NO. |
ITEM |
Technical Parameter |
|
1 |
Suitable Raw Materials |
Small pieces of Waste tyre,rubber, waste plastic≤5cm |
|
2 |
Operating Mode |
Fully Continuous Operation |
|
3 |
Structure |
Horizontal Type Revolve |
|
4 |
Loading and discharging |
Fully Automatic Feeding and Discharging under High Temperature at Same Time |
|
5 |
Capacity(24h) |
8-20Mt |
|
6 |
Work Pressure |
Slightly Negative Pressure |
|
7 |
Oil Yield of tyres |
40%-45% |
|
8 |
Reactor Rotational Speed |
1R/M |
|
9 |
Installation Power |
110kw |
|
10 |
Cooling Method |
Cycle water |
|
11 |
Type of Drive |
Sprocket Wheel |
|
12 |
Heating Method |
Hot Air |
|
13 |
Noise dB(A) |
≤85 |
|
14 |
Main Reactor Weight (MT) |
About 20Mt |
|
15 |
Total Weight(MT) |
About 45Mt |
|
16 |
Installation Space Required |
60m*20m |
|
17 |
Manpower |
2/shift |
|
18 |
Shipment |
5*40HC |
|
19 |
Delivery time |
≤70Days |
Continuous Waste Plastic Pyrolysis Plant
Continuous Waste Plastic Pyrolysis Plant,Continuous Plastic Pyrolysis Plant,Plastic Pyrolysis Plant
Shangqiu Jinpeng Industrial Co., Ltd. , https://www.recyclings.nl