July 30 Baotou Steel Market Price Quotes

The product name specification material steel factory/origin price (yuan/ton) is higher than yesterday's last week high line Φ6.5mm Q235 Baosteel 5760 -200 -200 -140 high line Φ6.5mm Q235 Xuan Gang 5760 -200 -200 - 140 Rebar Φ12mm HRB335 Xuan Gang 5950 -30 -30 100 Rebar Φ16-25mm HRB335 Xuan Gang 5560 0 0 60 Rebar Φ16-25mm HRB335 Steel 5560 0 0 60 Hot Roll 2.75*1500*c Q235 Steel 6300 0 0 0 Hot rolled coil 3.0*1500*c Q235 Steel cladding 6100 0 0 0 Hot rolled coil 4.75*1500*c Q235 Steel 5980 0 0 0 Hot rolled coil 8.0*1500*c Q235 Steel wrapped 5980 0 0 0 Cold rolled sheet 0.5*1000*C SPCC Steel cladding 7250 0 0 0 Cold rolled steel plate 1.0*1000*2000 SPCC Steel cladding 7100 0 0 0 Cold rolled plate 1.5*1000*2000 SPCC Steel cladding 7050 0 0 0 Cold rolled plate 2.0*1000*2000 SPCC steel cladding 7100 0 0 0 plate 8mm Q235 steel 6900 0 0 0 plate 10mm Q235 steel 6730 0 0 plate 20mm Q235 steel 6600 0 0 0 plate 20mm Q235 Jiuquan 6600 0 0 0 Welded pipe 1.5 inch Q235 Q235 5960 0 0 0 Welded pipe 2.5 inch Q235 Q235 5950 0 0 0 Welded pipe 4 inch Q235 Clad steel 5950 0 0 0 Seamless pipe 76*4.5mm 20# Angang 7700 0 0 -200 Seamless pipe 108* 4.5mm 20# Ansteel 7750 0 0 -350 Seamless Tube 159*4.5mm 20# Steel 7800 0 0 250 Seamless tube 168*8mm 20# Steel cladding 7700 0 0 300 Seamless tube 219*8mm 20# Steel cladding 8000 0 0 100 I-beam 25# Q235 Tangsteel 6300 0 0 400 I-beam 36# Q235 Baotou Steel 6400 0 0 500 Channel Steel 16# Q235 Tang Steel 5850 0 0 Channel Steel 28# Q235 Baotou Steel 5850 0 0 Angle Steel 5# Q235 Tangshan 5850 0 0 0 Angle Steel 8# Q235 Angang 5660 0 0 0

Anti-wear Ring

Installation and precautions of track connecting rod oil seal
The installation steps for the track link oil seal are as follows:
1. Cleaning: Clean the connecting parts to ensure that the surface is flat, clean, and free of grease and dirt.
2. Oil application: Apply a layer of lubricating oil to the connecting parts for better installation.
3. Installation: Gently push the oil seal into the connection area to ensure that the lip of the oil seal is not damaged.
4. Positioning: After positioning the oil seal, press it with your fingers to ensure it is in the correct position.
5. Inspection: Check if the oil seal is installed correctly and ensure that the lip is not damaged.
The precautions are as follows:
Before installation, check if the oil seal is damaged. If the oil seal is damaged, replace it with a new one.
Before installation, ensure that the surface of the connecting parts is flat, clean, and free of grease and dirt.
3. When installing the oil seal, gently push in to avoid damaging the lip of the oil seal.
4. After installation, check whether the oil seal is installed correctly to ensure that the lip is not damaged.
5. During use, the condition of the oil seal should be regularly checked. If any damage or wear is found, the oil seal should be replaced in a timely manner.

Wear ring for excavator,For excavator track,For excavator accessories

Safe Seal Technology Co., Ltd. , https://www.sprsealkits.com